“Monitor a heterogeneous IT infrastructure environment by deploying an infrastructure monitoring suite and leverage other IT operations management (ITOM) tools to fill functionality gaps… This provides better value when compared to a collection of similarly priced domain-specific products, since multiple features are now part of one offering.”

semoga di mengerti apa yang di katakan.nah kali ini kita akan mencoba menginstall centreon EMS untuk memonitoring perangkat jaringan kita menggunakan docker.

Dockerized Centreon 2.5.2

This is NOT well-tested. Please report all issues/requirements to either of the emails at the bottom of this page.
It works on two different installations but the result you see evolved while getting it to this stage..
Please report any problems!

Preparing the host

The configuration files and state data are stored on directories outside the container. We will mount external directories for all state that should not vanish when the container is regenerated:

• /docker-store/centreon/nagios-etc
• /docker-store/centreon/nagios-var
• /docker-store/centreon/centreon-etc
• /docker-store/centreon/centreon-var

You may place these folders somewhere else, just make sure you update the corresponding paths below.

Building the image

First step you do with this repo (if you cloned it) is to build it. Note that dot at the end referencing the current directory. Once that is done you have an image that you can run and that is tagged centeron for easier reference below.

docker build -t centreon .

If your prefer to pull directly from Docker

docker pull vegasbrianc/docker-centreon

Running the container

Now that's the easy part, as long as you remember to connect the right volumes:

docker run -i -t -p 8100:80 --name centreon \
  -v /docker-store/centreon/nagios-etc:/usr/local/nagios/etc \
  -v /docker-store/centreon/nagios-var:/usr/local/nagios/var \
  -v /docker-store/centreon/centreon-var:/var/lib/centreon \
  -v /docker-store/centreon/centreon-etc:/etc/centreon \
  -v /etc/localtime:/etc/localtime:ro \
  --privileged=true \
  centreon /bin/bash

The 8100 is the host TCP port under which the Apache Webserver inside the container will be available on the outside. Change as desired.
The /bin/bash drops you in a shell in exactly the situation where the container normally would execute /start.sh. If you omit /bin/bash, exactly that will be done (as specified as the CMD statement in Dockerfile). While running the container with bash, try /start.sh & to start the "normal" stuff and still be able to look inside the container for logfiles etc.
The need to run the container as a privileged container stems from the need to increase the kernel.msgmnb parameter.
The Centreon daemon centcore will not start and end up in a supervisord-FATAL state. That is expected, as the following setup will need to create the configuration files first. Nevertheless, the web interface works already.

Setting up Centreon

Once the container is running, you can reach Centreon under

http://host-server.example.com:8100/centreon/

Centreon will start the setup process. It is very opinionated and even requires you to hand over your MySQL root user password. Here are some hints for what values are needed:

• Monitoring Engine: nagios
• Nagios directory: /usr/local/nagios
• Nagiostats binary: /usr/local/nagios/bin/nagiostats
• Nagios image directory: /usr/local/nagios/share/images
• Embedded Perl initialisation file: /usr/local/nagios/share/p1.pl
• Broker Module: ndoutils
• Ndomod binary (ndomod.o): /usr/local/nagios/bin/ndomod.o

You may end up in an unescapable loop of Centreon trying to apply upgrades. It seems that it does not remove the install directory. If that happens, restart the container. /start.sh should now take care of that.
Centreon contains defaults that end up in the generated Nagios configuration. Those defaults need to be changed. Log into the web frontend as admin and go to:

Configuration -> Monitoring Engines -> `main.cfg` (left nav bar) -> `Nagios CFG 1`

Then change these values:
Files tab:

• Status file: /usr/local/nagios/var/status.log
• Log file: /usr/local/nagios/var/nagios.log
• Temp File: /usr/local/nagios/var/nagios.tmp
• Lock File: /usr/local/nagios/var/nagios.lock

Log Options tab:

• Log Archive Path: /usr/local/nagios/var/archives/
• State Retention File: /usr/local/nagios/var/retention.dat

Now click Save and generate the Nagios configuration files:

• Configuration -> Monitoring Engine -> Generate
• Click Export to see if any errors pop up. If not:
• Activate checkbox Move Export Files
• Activate checkbox Restart Monitoring Engine (Method: Restart)
• Click Export

Then stop and restart the container to give centcore a chance to start.

Fixing MySQL permissions

Centreon sets itself up with MySQL access rights from the IP address that the installation is running from. Inside a container, that IP very likely changes on restart, so it needs to be fixed.
Look for the centreon entry in table mysql.user that is limited to 172.17.xx.yy and change the host column to read 172.17.%. % obviously works too. Do the same thing in the mysql.db database.
Don't forget to FLUSH PRIVILEGES; before retrying.

Troubleshooting

NODUtils

It logs to syslog. If you see the following message, you need to increate the kernel parameter kernel.msgmnb:

ndo2db: Warning: Retrying message send. This can occur because you have too few messages
allowed or too few total bytes allowed in message queues.
You are currently using 64 of 2002 messages and 65536 of 65536 bytes in the queue.
See README for kernel tuning options.

Increasing the value on the host seemed like a reasonable thing, like so:

sysctl -w kernel.msgmnb=655360

65536 was too small in my case. Adding a zero did the trick and may be way too high. This only works when running the container with --privileged=true and running sysctl -w as above from inside the container. Running it on the outside yields 16384 inside the container, no matter what you do. Doesn't make sense? Yeah, doesn't. Sorry.

Centreon not showing any services or hosts under 'Monitoring'

Check for errors from ndo2db in syslog. See above.

TODO

• Cron-Jobs are not handled yet (see /root/nagios/centreon-2.5.2/tmpl/install/*.cron)

Mari kita kenali sedikit tetang apa dan bagaimana cara kerja PHP NetMap dan berikut penjelasan dalam bahasa inggrisnya.

PHPNetMap

PHP Software for network device monitoring with SNMP v(1/2c/3) protocol. Tested with 3Com/HP, ProCurve, Dell and Extreme devices. Some other models with SNMP support work properly. Framework yii with Bootstrap Colorpicker andCAdvancedArBehavior. Using JavaScript D3 library to the map.

How It works

The PHPNetMap shows connected hosts based on the FIB or table CAM switches, and ARP table devices. You can perform searches within these tables in various devices with the Search form. With the map view you can check the connections between hosts and each host there is a screen indicating the port status with their respective connected host. You can see the operating status port and status of the Spanning Tree Protocol on switches with dot1dStpPortState OID. Using an SNMP community with read/write permission you can change the ifAdminStatus or set ifAlias.

PHPNetMap and Docker

I created a Docker image with all the configuration ready for use PHPNetMap, available in Docker Hub. With the docker-compose.yml in the project root you can download the image and run system only with the command docker-compose up within the directory project. Note server settings to run in production mode (Password in ADMIN_PASSWORD environment variable, for example). Change the docker-compose.yml as necessary.

Installing Docker

curl -ssl https://get.docker.com/ | sh

Create and run a single container

docker run -p 80:80 --name=server1 marcelofmatos/phpnetmap

Open a web browser and access http://<server_ip> or http://localhost if 'docker run' executed in your local machine The HTTP user is 'admin' and password is string set in ADMIN_PASSWORD environment variable.
If you wish run container in other port:

docker run -p 8081:80 --name=server1 marcelofmatos/phpnetmap

And open http://localhost:8081
To manage container:

docker start server1
docker stop server1

Set HTTP user and password:

docker run -p 80:80 --name=server1 -e ADMIN_USER=admin -e ADMIN_PASSWORD=pnm marcelofmatos/phpnetmap

If ADMIN_USER is not set, 'admin' is default value. If ADMIN_PASSWORD is not set, a random value is set and printed on log container.
To show log container

docker logs server1

See more in
https://docs.docker.com/engine/getstarted/
https://github.com/marcelofmatos/phpnetmap